![EricaceaeCalluna](/img/default-banner.jpg)
- Видео 3
- Просмотров 334 206
EricaceaeCalluna
Добавлен 6 окт 2010
Braun Coffee Grinder Model 4041 Replacement
How to put your Braun coffee grinder back together when you try to replace the blade, but take it apart instead.
I originally got my blade from Electric Shaver Store in Lincoln, NE.
Braun Coffee Grinder Crushing Blade, Type 4041, KSM2, KSM4 but as of March 4, 2016 they no longer have them.
Today I ordered a new blade from ereplacementparts(dot)com. Braun Cutting Blade - 64041622 $1.99 + $5 S&H.
I originally got my blade from Electric Shaver Store in Lincoln, NE.
Braun Coffee Grinder Crushing Blade, Type 4041, KSM2, KSM4 but as of March 4, 2016 they no longer have them.
Today I ordered a new blade from ereplacementparts(dot)com. Braun Cutting Blade - 64041622 $1.99 + $5 S&H.
Просмотров: 118 872
Видео
GE Triton Escutcheon Replacement
Просмотров 2,1 тыс.12 лет назад
Replace the escutcheon (top portion of the door panel) of a dishwasher. Cost about $40 for the part delivered. Hardest part was 'guessing' where all the screws were and getting that spring to stay on the post. Other then that it went pretty easily. Use the door latch to keep the top part of the door out of the way. Use a couple of books to hold the bottom part of the door down. This is not a gr...
How to Change a Brake Light on a 2005 Nissan Altima
Просмотров 213 тыс.13 лет назад
This is a real time video on changing a brake light in a 2005 Nissan Altima. I've pointed out some helpful information: -how to release & easily replace the weather stripping/carpet cover -how to remove the cargo net connector -a standard socket won't reach over the bolt, I had to use an adjustable wrench but just to loosen the nut/washer; I then used my hand to remove them -location of plastic...
Hello all. I have disassembled mine but now cannot get the “switch” to push the contact that makes the unit run. I see the clear part goes into the t shaped slot, but no matter how I press the button, it will not push the terminal enough to make it close the circuit and start. Any suggestions?
Helalin var 🙏🙏
Can you please send address to order Blade 🙏 appreciate thanks
They are not available any longer except eBay. I saw one there for $22. Search: Braun Cutting Blade - 64041622
@EricaceaeCalluna OK thanks
Hi just wanted to know how do u take the motor out of the case to fit bowl and how to attach the t piece which is attich to motor. Could u please help me
Well you're going to have to watch the video and do the steps in reverse. Basically there's two screws that hold the motor mount onto the base. I wouldn't recommend it unless you absolutely feel you need to though. Watch the video and I'll point out things that you'll need to take into account again in reverse. The cord the alignment of the gasket. The alignment of the crosshairs on the base motor. The alignment of the screw holes.
Thank you ❤️
Was helpful in seeing just where the vertical on switch mechanism lined up. I've had this apart several times over the past decade+ but got on that this time around for some reason. Coffee build up inside causes the on switch to stick on. Thanks for taking the time to create this video.
That plastic tab is not pointing straight up on my grinder but is sticking out for some reason. It must have happened when I pulled the motor out. How to I fit it back into the slot on that plastic thingy on the side? Help?
I’m here 12 years later to say, thank you for helping me fix my car!
Hi. Where can I order the blades?
does anyone know where to order a new blade, I only see used blades on ebay
I bought new ones last Year from ebay to keep on hand.
@@EricaceaeCalluna Canada here. Individual blades on eBay not happening. Can buy a whole grinder there but with S&H on top of the unit I might as well buy a completely new mini blade grinder. Bummer.
*Have had 3 of these units in the past 20+ years. They are good grinders **MyBest.Kitchen** what most if not all the complaints are about concerns a small pop-up switch in the bottom of the unit where the clear plastic hopper slides in. Please don't throw the unit away when nothing happens after pressing the start button. Just take the hopper out, clean @ the pop-up switch or vacuum the area around the switch and I think you'll find that it turns on. Hope this helps....have read reviews where the unit only worked for one grinding, then mysteriously quit working. Again, clean the switch it will most likely solve the issue.*
Thank you so much
thanks LOL
Thank you
Almost 9 years after posting, this video is still so useful. Thank you!
I love you... Thank you. That is all
Nissan bad Design what the fuck y. Thanks for video
*EDIT: They emailed me after I purchased the blade saying that the item is out of stock. They did not charge my card. I will look and see if any other website has the part. I don’t think I will find one. The aftermarket 3D printed lid is in stock. I am not sure about the OEM lid.* *11/3/2020* ShaverSpot is the only place online that still sells this part. I looked everywhere to find other places that sell this part. They all list out of stock. I just ordered the part. The blade is $6.99 and shipping is $9.98. In total it cost me $16.97 for the blade. It is expensive, but I think it is worth it. www.shaverspot.com/catalog2/product_info.php/products_id/271?osCsid=8fc4cc3fd9fc67833cdda66091fcc55d ShaverSpot also sells an original replacement lid. I bought a sturdier 3D printed lid off eBay. www.shaverspot.com/catalog2/product_info.php/products_id/272?osCsid=8fc4cc3fd9fc67833cdda66091fcc55d White - www.ebay.com/itm/143819629538 Black - www.ebay.com/itm/143730347243
The motor on mine seized up. Upon disassembly, I found it was simply so gunked up and corroded that the motor shaft would barely turn. If you have this problem, try this: 1. Remove the circlip on the bottom of the motor shaft. It's the C-shaped thing that fits in a groove at the end of the shaft and keeps it in place. Don't lose it. 2. Drip Liquid Wrench ("penetrating oil") around where the top-side shaft enters the motor (the end that the blade attaches to). 3. Tap the bottom of the shaft with a hammer, hard enough to move it up a little bit. It doesn't go that far, because the internal motor parts limit it. Now tap the top of the shaft with the hammer to push the shaft back down. Repeat this, moving the shaft back and forth and turning it until you've worked the penetrating oil into the grime and loosened the shaft. 4. When the shaft spins pretty freely, wipe off as much of the Liquid Wrench as you can, moving the shaft back and forth to expose more to wipe. Re-lubricate it with a light oil. I dripped some on both ends of the shaft. I used Tri-Flow, which is big with bicyclists. Not sure what the best choice is here, but I would NOT use WD-40: It gums up over time.
This was a great video. Thank you! Others made it pretty clear how to take it apart, but not how to reassemble. Also, the trick for simple blade replacement, using the slot in the bottom could have saved me a lot of hassle. Sigh... I will note that replacement blades are VERY hard to come by now. Braun, Amazon, ebay and ereplacementparts no longer carry them. I had to resort to buying a used KSM2 with a faulty motor for parts and do some pilfering. The actual blade was in mint condition, but the plastic cap (with threading house) was cracked open. It works, but isn't very pretty and I'm sure plastic fragments can get into the grinds. I'm going to try to rebuild that housing using epoxy putty, letting it dry, sanding, and re-threading the new part of the cap, but I'm still on the lookout for a mint replacement blade.
Check out the pinned comment from 11/3/2020 for an online retailer who still sells the blade!
Muchas gracias 🌹. Saludos y bendiciones
Anyone know where to get replacement blades from?
I have opened from, but how disassemble the blade and steel bowl
They make trash equipment
Как разобрать и собрать свою кофемолку Braun при замене лезвия. Я купила свое лезвие в магазине торгующем электробритвами в городе Линкольн, Небраска. Это лезвие для дробления к кофемолке Braun, тип 4041, KSM2, KSM4. Я каждый день молола кофемолкой миндаль для французских макарон, но она сломалась. Она перестала молоть. Оказывается это случилось из-за поломки лезвий. Что же я сделала. Я заказала новую запасную часть для кофемолки Braun с номером 4041. Я нашла ее в интернете за 3,97 $ с доставкой. Мне прислали ее буквально в течение двух дней, и я могу отремонтировать мою кофемолку. Ну, позвольте мне показать вам, как я это сделала. Я нашла в интернете, как вставить плоскую отвертку в эту щель. Тем не менее я не поймала винт. Вместо этого, эти два отверстия ведут прямо к головкам винтов под крест, которые я уже выкрутила. Они были там. Их два, по одному на каждой стороне. И я сняла их. Таким образом я могу снять двигатель. Почему я хочу снять двигатель? Потому что мне нужно было устойчиво держать эту часть, вот этот винт с плоской головкой чтобы я могла открутить мое лезвие. Я также очистила внутри, но там было не так много грязи, ну и заодним прочистила чашку тоже. Вы должны вставить эту часть обратно как бы 'вверх ногами', если понимаете о чем я. Видите там плоская сторона и круглая сторона. Так что я сейчас это выровняю, а затем покажу вам еще одну вещь - эту пластиковую часть, которую необходимо выровнять с T слотом на боку, таким образом она давит на медный провод тем самым создавая контакт и активируя двигатель. Я теперь все по быстрому соберу обратно выравнивая этот слот вот с этим здесь чтобы потом вставить на дно лотка.... Вот и дно лотка снова здесь. Я расскажу вам секрет, если вы будете снимать эту часть, видите ту плоскую сторону? Используйте ее в свою пользу когда будете вставлять сюда на дно. Используйте плоскую сторону чтобы не мешали эти выпирающие части. Как я уже говорила, будем делать вверх ногами.Что у нас ... Это как шайба, резиновая шайба. Это сторона квадрата, как вы видите, что это квадрат и круг, который идет вниз и внутрь. Я ее выровняю отверткой. Так, сейчас все прекрасно выровнено. Как я уже говорила, этот слот идет ... Это как защелка А в отверстие B. Таким образом, есть отверстие B, есть защелка А .... А это закрепляется в ту выступающую часть. Видите, рядом с медной проволокой? Это пластиковая частичка куда все это закрепляется. Поэтому, когда кнопка нажата, медный провод создает контакт, что и запускает двигатель ... Ладно, наткнулась на другую проблему, которой я хотела бы поделиться. Тут есть 4 выступа в основании мотора, которые заходят в пазы. Вы видите отверстия? Вот сюда входят выступы, но я должна убедиться, что эти винтовые пазы совпали там с резьбовыми отверстиями. Это не так то просто. Итак, еще раз, если вы сможете найти достаточно длинную отвертку, размера которой хватит чтобы вставив через эту основу достичь винт, то такой вариант будет наилучшим. Опять же, еще одно замечание. Когда вы будете ставить крышку обратно на базу, это резьба под электрический шнур. Вы должны дать ему слабину, я просто хотела предупредить вас. Хорошо, так что я опустила крышку вниз, вы можете увидеть, я уронила один из винтов, и вы можете видеть, отверстия как по волшебству, выстроились почти отлично. Если бы у меня была достаточно длинная плоская отвертка..... Делайте все возможное, чтобы прислушаться к моему совету... Всегда отключайте электронику, прежде чем работать с ней. Используйте тонкую длинную плоскую отвертку и выравнивайте ей ... Сейчас это не выровнено. Надо выровнять отверстия с винтами ... Так, они выстроились ровно. Я поставлю эту плоскую отвертку, и мне надо довольно сильно нажать. Пожалуйста, обратите внимание, что эти новые лезвия довольно острые, но они снимаются также точно. Откручивается влево... Ой, я не хочу порезаться. И вправо-затянуть. Так против часовой стрелки, чтобы открутить его, и по часовой стрелке, чтобы закрутить. Я быстро проверю. Я сделаю сахарную пудру из сахарного-песка, это довольно быстро. Это лезвие очень острое, есть огромная разница со старым. Вы будете делать правильно, когда вы вставите тонкую длинную плоскую отвертку в отверстие, выровняйте отверстия с лицевой стороны ... Возьмите тряпку или полотенце. Это надо делать двумя руками. Вы должны устойчиво держать ее за дно, а затем повернуть против часовой стрелки, чтобы снять его, а затем по часовой стрелке, чтобы вернуть его на место. Я просто не рекомендовала бы брать этот друг от друга. Я сделала, она сейчас работает. Сверх быстро. Замечательно. Заменить лезвие это дешево. Конечно, я знаю, что кофемолки дешевы, но заменить лезвие все равно намного дешевле. Это стоило мне 8 $. Двигатель хороший и еще поработает.
THANK YOU SO MUCH FOR MAKING THIS VIDEO>.. you saved my coffee grinder.. i had to put a little WD40 on the armature.. and BAM back to good.. thanks again J
Thanks
I have one of these grinders, only the design on mine is one that I cannot find on the "Internet" ANYWHERE...I have something that simply cannot be found....I've searched and searched...no dice...it's really irritating me...I dont know how else to find documentation of its existence....the design is a black grinder, with a gold ship in a port type scene...cannot find it ANYWHERE online
*It is good coffee grinder▪▪▪>**allmy.tips/HamiltonCoffeeGrinder?55c ** A little loud if you use it in the office, but not too bad. Had no complaints from coworkers about the noise. Easy to grind for small quantities and for larger pots of coffee.*
Thank so much for this video. You are really good. I am a guy and could not figure it out. I was becoming like super frustrated. (LOL). I love these youTube DIY videos.....saves me so much time, money, energy, and frustration! 👍👍👍👍👍
Great Video 👍.
Thank you! The most informative tutorial on this from beginning to end. It takes a Woman to explain in full detail what we need to know.
Thank you for this, just fixed mine the inside wire would not touch so i adjusted it
Awesome video! Thank you. I was going to take it to my mechanic but to heck with that! I’ll do it myself. Many thAnks!
Thank you this was very helpful!!!
Lifesaver. Thanks for the helpful demo.
There are many ways to fix. I think the simplest is few drops of super glue - very in expense. If the blade does not budge on activation, then it's the motor problem. If it turns, but slips the blade has come loose from the motor shaft. Quick test is turning the blade by hand - it will take little force to turn. If you can turn the blade easily, then its the case of stripped thread You can replace the blade if you like.I think it's a overkill and expensive and not a easy job. In most cases it's case of cracked nut or stripped thread. The blade does not go bad easily. Caution: In most cases the glued may have dripped below into the casing. Make sure to give the blade few turns, so that it will break loose of any casing binding. If the plastic nut is cracked exposing the shaft thread - then squeeze few drops of super glue onto the shaft. This will bind the blade to the shaft. If the shaft thread is not cracked, squeeze the head of the plastic nut with pliers. This will crack the plastic and will expose the motor shaft thread.
Well done. I have a broken blade in a Hamilton Beach Mdl. 80344. It has the windup hidden cord on the bottom that makes it a bit more difficult to get to that critical screw. But with some tips from you, I got the blade off and I don't think I broke any of the cord winding pieces. Now just need to find a new blade. Fortunately, I also have this Braun unit so I can compare if the blades look interchangeable. Update: May 17, 2018 ereplacementparts doesn't stock anymore and Amazon price is $75 + $5 shipping!! Please leave a comment if you know where they can be found. Found at PickeringAppliances.ca for $12.95 but I think they only ship to Canada.
How docypu get coffee out of it? Intuitively I put it on it‘s head after grinding so the coffee falls into the lid, but that is not perfect since a little bit of coffee gets in between the plastic. Do you just go in with a spoon? I think that‘s even worse? Am I not seeing some arcane knowledge here? :D
Where to find this such a knife Braun coffee grinder because I have the same model and the same problem. I live in Serbia in Nis. This mill we received from relatives in Munich back in 1990. Greetings from sunny Nis.
ive just ordered a cheap one for me in Moscow
you are so good , i wish i have a wife lke you hahaha
Just get a 5/16" drill bit and widen the flat-head screw slot to a round hole. The plastic is soft so be careful. Don't press down hard on the drill. It only takes a second. You could probably widen the hole with a sharp box cutter or something sharp.
Thank you very much. I also had to take mine apart to properly hold the bottom screw in place. Without your help I never would have figured out about the T-slot. Now my grinder is repaired and working. Hopefully, it will last me another 20 years.
Thanks you very much, you give me helps to remove correctly blade on my very old coffee grinder (apparently not branded).
My light is stuck after i took off both screws. Smh
This is a great video.Not only helpful procedure steps, but also excellent details with practical tips for each nut, clip, carpet, etc.. I've done this once but doing it again this week so this is a big help. Thank you. .
Three thousand "review" videos later I finally find your useful video on how to take this booger apart. Thank you.
Very nice video.
Thanks to this video, I was able to change my break light! Hardest part was outside carpet plastic nut. Poorly designed piece.